RON vs MON is a comparison of two octane numbers measured on the same test engine under different conditions. Research Octane Number (RON) is measured at 600 rpm, Motor Octane Number (MON) at 900 rpm with a higher mixture temperature. RON reflects milder, lower-speed knock resistance; MON reflects harsher, high-load operation. A booster must be judged on both.
A blend can clear its RON target and still miss the specification, because the booster lifted one number and barely moved the other. This guide walks from the basics to a trial method, so you can judge any octane booster before it reaches the pool.
Why this matters now
- India’s petrol pool is changing. Autocar India reported on 27 February 2026 that the government had mandated petrol of at least 95 RON from 1 April 2026, one year after the E20 rollout.
- The same report quoted oil companies as putting regular petrol at around 91-92 RON and E20 closer to 97-98 RON (Autocar India, 2026).
- Ethanol-rich blends change how RON and MON move relative to each other, so a booster that worked on a hydrocarbon-only pool may behave differently.
Level 1, Beginner: What are RON and MON?
Octane number is a fuel’s resistance to knock, measured against reference fuels. By definition, isooctane is 100 and n-heptane is 0 on both scales. A fuel with an octane number of 95 knocks like a blend of 95 percent isooctane and 5 percent n-heptane.
Both numbers come from the same single-cylinder, variable-compression-ratio CFR engine, using ASTM D2699 for RON and ASTM D2700 for MON.
- RON runs at 600 rpm and a moderate mixture temperature.
- MON runs at 900 rpm with a higher mixture inlet temperature.
- MON is usually lower than RON for the same fuel because its conditions are harsher.
Level 2, Intermediate: What is octane sensitivity, and why does it matter?
Octane sensitivity is the difference between a fuel’s RON and its MON. A fuel with RON 95 and MON 85 has a sensitivity of 10. Sensitivity tells you how much the fuel’s knock resistance drops when conditions get harsher.
- One technical page reports typical sensitivity of about 9 units for US regular and 10 for premium gasoline..
- Anti-knock index (AKI) is the average of the two, (RON + MON) / 2, and is the number posted on US pumps under the FTC Fuel Rating Rule.
- India and Europe set limits on RON and MON separately in their motor gasoline standards, so a blend must pass each.
Why two limits exist is practical. RON tracks everyday part-load driving. MON tracks high-speed, high-temperature, full-throttle conditions, where one technical source notes it is the better indicator of knock resistance.
Which component choices raise sensitivity?
Components rich in aromatics, olefins and ethanol tend to have high RON with a bigger gap to MON. Paraffinic and alkylate-type streams tend to have a smaller gap. Ethanol in particular lifts RON strongly, so E20 pools can show high RON with a wider sensitivity.
This is why a booster that is described only by its effect on RON can mislead. If the pool is already MON-constrained, extra RON does not help.
Level 3, Advanced: How do you evaluate an octane booster?
Evaluate a booster by measuring both RON and MON on the finished blend, at several dose levels, against your own base gasoline. A data sheet number measured in a neat or reference fuel will not tell you how the product behaves in your pool.
Use the gap-first rule. Work out how far the blend is below the RON target and below the MON target, then size the dose to whichever gap is larger. The other number will usually clear on its own.
- Fix the base: use one well-characterised base gasoline batch for the whole trial, and record its RON, MON, distillation, vapour pressure and ethanol content.
- Run a dose-response series: test at least three dose levels plus an undosed baseline, with RON by ASTM D2699 and MON by ASTM D2700 on every sample.
- Respect precision: compare the measured improvement with the repeatability and reproducibility limits in the test methods. A gain smaller than the test’s own scatter is not a result.
- Expect non-linear response: octane blending is not a straight average, so the gain per unit dose usually falls as dose rises. Look for the knee of the curve.
- Check the rest of the specification: vapour pressure, distillation, gum, corrosion and material compatibility must all still pass, including with ethanol.
- Price the giveaway: any octane above the specification is cost without value. Set the dose to hold the limit with a stated margin, not above it.
Common mistakes in booster trials
- Judging on RON alone when MON is the binding limit.
- Using a single dose level and assuming the response is linear.
- Changing the base gasoline between runs, so the effect of the booster cannot be separated from the effect of the base.
- Ignoring the ethanol content, which shifts the relationship between RON and MON.
Quick Answers
- Which is higher, RON or MON? RON is usually higher than MON for the same gasoline, because MON is measured under harsher conditions.
- What does 95 RON mean? It means the fuel resists knock like a blend of 95 percent isooctane and 5 percent n-heptane under the RON test conditions.
- Does a higher octane fuel give more power? Not by itself. Higher octane only helps an engine designed to use it, by resisting knock.
Next step
Before the next booster trial, list your RON and MON targets, your current blend values and the gap to each. Make the larger gap the dose target, and run both tests on every sample.
When your pool changes, for example with more ethanol, which number moves first in your blend: RON or MON?
Key Takeaways
- RON is measured at 600 rpm and MON at 900 rpm with a higher mixture temperature, both on a CFR engine (ASTM D2699 and D2700).
- Sensitivity is RON minus MON. A booster described only by its RON effect can mislead when MON is the limit.
- Anti-knock index is (RON + MON) / 2, used on US pumps. India and Europe specify RON and MON separately.
- Use the gap-first rule: size the dose to the larger of the RON gap and the MON gap.
- Judge a booster on the finished blend with a dose-response series, both tests on every sample, and the full specification checked.
FAQ
What is the difference between RON and MON?
Both measure a gasoline’s resistance to knock on the same CFR engine. RON runs at 600 rpm, while MON runs at 900 rpm with a higher mixture temperature. MON is therefore the tougher test and usually reads lower than RON. Specifications often limit each number separately, so a blend must pass both.
What is octane sensitivity?
Octane sensitivity is RON minus MON for a given gasoline. It shows how much knock resistance falls when operating conditions become more severe. One technical source reports typical values near 9 for US regular and 10 for premium gasoline [VERIFY: year], and ethanol-rich blends tend to show wider gaps.
What is the anti-knock index?
Anti-knock index (AKI) is the average of RON and MON, written (R+M)/2. It is the octane number posted on US pumps under the FTC Fuel Rating Rule. Markets that post RON, such as India, specify RON and MON limits separately, so AKI is not directly comparable to a RON figure.
How do I test an octane booster?
Measure RON by ASTM D2699 and MON by ASTM D2700 on the finished blend, at a baseline and at least three dose levels, using one fixed base gasoline. Compare gains with the repeatability limits of the methods, and confirm vapour pressure, distillation and ethanol compatibility still pass.
Is higher octane better for every engine?
No. Octane measures resistance to knock, not energy content. An engine designed for lower octane gains little from higher octane fuel, while an engine designed for higher octane needs it to avoid knock. The right grade is the one the engine manufacturer specifies for that engine.